Freedom Appliances explains how to test an electric stove element so you can find the real fault before you replace any parts. A burner that stays cold is not always a dead element. The cause might be a loose connection, a worn socket or a failed switch. A few careful checks separate these problems quickly. This guide walks through the safe steps, the warning signs and the point where a technician should take over.
Electric stoves use two main styles. Coil elements are the removable spirals that plug into a socket. Smooth-top stoves hide the elements under glass, so they are not removable at all.
Coil burners are easier to check at home. You can lift them out and inspect the ends. Smooth-top elements need a technician with proper tools because the glass is fragile. Identify your style before going further.
Elements also differ by size. Small burners draw less power than large ones, and some ranges have dual-ring elements. Your manual lists the type for each position.
Industry estimates suggest a coil element often lasts around 5 to 10 years with normal use. Spills, bent coils and heavy pans shorten that range. Knowing the typical lifespan helps you decide whether a failed element is simply worn out or a sign of a deeper fault.
Electricity and heat make this job risky if you rush. Follow these steps every time:
1. Turn all burner knobs to off.
2. Let the stove cool for at least 30 minutes.
3. Switch off the stove at the breaker panel.
4. Wear dry shoes and work in good light.
5. Keep children and pets out of the kitchen.
Never test a live circuit with a meter unless you are trained. A tripped breaker or a burning smell means you should stop and call a professional. If you also notice that the breaker trips, read our guide on a stove tripping the breaker.
Many faults show up before you pick up a meter. Start with your eyes and a torch. Remove the coil by pulling it gently straight out. Then look closely at the element and the socket.
Check the coil for blisters, bulges, burn marks or breaks. Look at the metal prongs for black discolouration. A blistered coil usually means the internal wire has failed. Replace it with the same model number from your stove's manual.
Inspect the socket for melted plastic, scorched wires or loose terminals. A burnt socket often points to a poor connection that has overheated. The element may be fine while the socket is damaged. Replacing only the element will not solve that problem.
The swap test is the easiest check. If your stove has two burners of the same size, swap the coils. Turn the stove back on and test both positions. If the fault follows the coil, the element has failed. If it stays in the same position, the socket or switch is the culprit.
A continuity test uses a multimeter on the ohms setting. With the element removed and cool, touch the probes to both terminals. A reading of a few ohms up to roughly 100 ohms usually indicates a good coil. A reading of infinity means the wire inside is broken. Always check the multimeter manual before use.
When you test an electric stove element this way, record your readings. They help a technician understand what you have already ruled out. Note the date, the burner position and the reading. A clear record saves diagnostic time on the visit.
Do not force a coil into a damaged socket. Do not bend the terminals back and forth, because the metal fatigues and snaps. Never use a wet cloth near the connections. Avoid mixing element sizes, since a wrong-size coil can overheat the socket.
Another common mistake is testing a hot element. Heat changes resistance and can give a false reading. Wait until the part feels cool to the touch before you measure.
The table below links what you see with what is usually behind it.
| Symptom | Likely cause | What a technician does |
|---|---|---|
| One burner stays cold | Failed element or loose socket | Tests element, socket and wiring |
| Burner heats weakly | Worn element or infinite switch | Tests resistance and switch output |
| Burner stays on high | Stuck infinite switch | Replaces the switch |
| Sparks or crackling | Damaged socket or loose plug | Replaces the socket and terminal block |
| Two burners dead | Supply or breaker issue | Checks voltage at the terminal block |
| Oven works, burners do not | Surface switch or wiring fault | Traces wiring and tests switches |
If the burner heats unevenly, see our article on an electric coil stove not heating evenly. For one dead burner, read about an electric stove burner not working.
Some faults hide behind the panel. The infinite switch, the terminal block and the wiring harness all carry high current. A poor connection can overheat and cause damage or fire.
Learning to test an electric stove element is useful, but live-wire work is different. Technicians use calibrated meters, insulated tools and proven procedures. They also confirm that a new part works safely before leaving. That protects both your stove and your home.
Natural Resources Canada publishes general information on Natural Resources Canadaโs EnerGuide information for stoves and cooktops, which is a good starting point for homeowners. Still, no website replaces a trained inspection of live wiring.
Contact a technician if you see burn marks on wiring, smell burning plastic or find that the breaker trips repeatedly. Do not keep using a stove that crackles, sparks or glows unevenly. Those signs mean the fault could worsen.
Our stove repair team in Calgary tests elements, switches and wiring, then explains the findings before work starts. An honest quote is given after assessment, so you stay in control of every decision.
How do I know if my stove element is bad?
Look for blisters, breaks or burn marks on the coil. A swap test with another burner of the same size also works well. If the problem follows the coil, the element has failed.
Can I replace an electric stove element myself?
Coil elements often plug in and can be changed by a careful homeowner after the power is off. Smooth-top elements need a technician. Always match the part number from your manual.
Why does my new element not work?
The socket, switch or wiring may be damaged. A new element cannot fix those faults. A technician can test each part in turn.
Is it normal for a stove element to smoke the first time?
A new element can give off light smoke or odour as protective coatings burn off. It should stop after a short time. Heavy smoke or sparks need immediate attention.
Ask about your stove or book a visit today.
Same day service ย โขย Red Seal certified ย โขย $79 service call